Slime Tube Sealant is a specially formulated liquid which is injected into the inner tube through the valve (the valve core has to be removed first). Slime Tube Sealant prevents and repairs flat tyres caused by puncturing objects up to 3mm in diameter. Slime Tube Sealant works repeatedly for up to 2 years. When a puncture occurs Slime Tube Sealant moves into the hole and the clotting agents are activated, effectively filling the hole and blocking the loss of air

Slime Tube Sealant:

• Instantly seals up to 1/8" (3mm) punctures for up to two years
• Non-toxic and non-hazardous
• Non-flammable
• Environmentally friendly and cleans up with water
• Effective under the most extreme temperatures: Low freezing point of -35˚F (-37˚C) and a high separation point of 182˚F (82˚C)
• Uses Fibro-Seal technology
• Requires air

Tyres must be kept fully inflated at all times for Slime Tube Sealant to work effectively, as it is the air inside the tyre/inner tube that forces the Slime Tube Sealant into the hole to seal it.
The wheel needs to be rotating for the Slime to coat the inside of the tyre/inner tube, so if the tyre loses air, re-inflate it and spin the wheel, this helps the Slime to seek out the puncture and hopefully seal it.

Guide to Fitting Pram Tyres and Inner Tubes

If you are just fitting a new inner tube:

1. Remove your wheel from the pram, (not always necesary but makes life easier).
2. Deflate the inner tube, once the air is out, pinch the tyre walls together to make it easier to lever off.
3. Use a tyre lever, or two levers if your tyre is tight, and lever one side of the tyre off the rim.
4. Remove the inner tube, and then you can take the tyre off completley.
5. Check the wheel for any sharp objects / rough surfaces that could cause a puncture
6. Check the tyre (if not replacing) for any sharp objects, do the by running your fingers around the inside carefully and remove foreign objects.
7. Once happy, put one side of the tyre back on the rim
8. Inflate your new inner tube only just enough so it has a "bit of shape", this will make it much easier to fit - Don't try to fit a fully deflated "floppy" inner tube as you will probably nip it when fitting.
9. Put the semi inflated inner tube in the valve hole of the wheel, and push the tube up into the tyre.
10. Now you can put the other side of the tyre on the rim, if possible do this with your thumbs as levering a tyre on can sometimes pinch the inner tube. If you do need to use tyre levers be careful not to damage the new tube.
11. Once the tyre is on you can inflate to the recommended PSI, you can use some Schwalbe Easy Fit to help the tyre slip into place under the rim bead. Its not always necesarry but makes it easier. You can also use fairy liquid! but you'll need to clean that off after.
12. Finally, check to make sure the tyre bead is seated properly on the rim.
13. Now just put your wheel back on and you're good to go.

If you are replacing the tyre and the inner tube

1. Remove your wheel from the pram, (not always necesary but makes life easier).
2. Deflate the inner tube, once the air is out, pinch the tyre walls together to make it easier to lever off.
3. Use a tyre lever, or two levers if your tyre is tight, and lever one side of the tyre off the rim.
4. Remove the inner tube, and then you can take the tyre off completley.
5. Check the wheel for any sharp objects / rough surfaces that could cause a puncture
6. Once happy, put one side of the new tyre on the rim
7. Inflate your new inner tube only just enough so it has a "bit of shape", this will make it much easier to fit - Don't try to fit a fully deflated "floppy" inner tube as you will probably nip it when fitting.
8. Put the semi inflated inner tube in the valve hole of the wheel, and push the tube up into the tyre.
9. Now you can put the other side of the tyre on the rim, if possible do this with your thumbs as levering a tyre on can sometimes puncture the inner tube. If you do need to use tyre levers be careful not to damage the new tube.
10. Once the tyre is on you can inflate to the recommended PSI, you can use some Schwalbe Easy Fit to help the tyre slip into place under the rim bead. Its not always necesarry but makes it easier. You can also use fairy liquid! but you'll need to clean that off after.
11. Finally, check to make sure the tyre bead is seated properly on the rim.
12. Now just put your wheel back on and you're good to go.

TIGHT & UNEVEN FITTING TYRES:

• Another useful tip for fitting tight tyres, or tyres that you are having trouble sitting evenly on the rim, is to warm them up first, on a radiator or in a warm airing cupboard. This makes them more pliable and a bit easier to fit.

MIS-SHAPED TYRES:

It is a good idea to warm up the tyre and manipulate it to get it as near to normal shape as possible. Mis-shaped tyres are fitted the same way as any other tyre, but special attention should be paid to the part of the tyre which is misshapen. Once the tyre is on the wheel you should inflate it a little at a time and make sure the misshapen part is not coming off the rim, if it is simply push it back into position and add a little more air.

ALWAYS KEEP MIS-SHAPED TYRES INFLATED TO THE MAXIMUM P.S.I.